| Age | Commit message (Collapse) | Author |
|---|
|
With b4450f1dd6bca537e60406b2383ab154a3e1485f we dropped what we
calculated here later on and now that we don't need it in the meantime
either we can just skip the busy work by default and expect dpkg to do
the right thing dropping also our little "last explicit configures"
removal trick introduced in b4450f1dd6bca537e60406b2383ab154a3e1485f.
This enables the last of a bunch of previously experimental options,
some of them existing still, but are very special and hence not really
worth documenting anymore (especially as it would need to be rewritten
now entirely) which is why the documentation is nearly completely
dropped.
The order of configuration stanzas in the simulation code changes
slightly as it isn't concerning itself with finding the 'right' order,
but any order is valid anyhow as long as the entire set happens in the
same call.
|
|
Using Pkg.CandVersion() here is wrong as its implementation will return
a candidate based just on the default policy settings ignoring user
preferences and otherwise set candidates (aka: it sidesteps the
pkgDepCache).
This causes M-A:same libraries to be detected as screwed even through
they aren't, so that they end up being kept back.
Reported-By: Felipe Sateler on IRC
|
|
This doesn't allow all tests to run cleanly, but it at least allows to
write tests which could run successfully in such environments.
Git-Dch: Ignore
|
|
Gbp-Dch: ignore
|
|
We use test{success,failure} now all over the place in the framework, so
its only consequencial to do this in the situations in which we test for
a specific output as well.
Git-Dch: Ignore
|
|
It is sometimes handy to have an installed package also in the archive,
but this was until now harder than it should as you had to duplicate the
lines, which is especially dangerous while writing the tests as it
easily happens that these two lines divert and so the same-but-different
version detection kicks in.
Git-Dch: Ignore
|
|
Previously, we had a start and a done of the calculation printed by
higher-level code, but this got intermixed by progress reporting from an
external solver or the output of autoremove code…
The higherlevel code is now only responsible for instantiating a
progress object of its choosing (if it wants progress after all) and the
rest will be handled by the upgrade code. Either it is used to show the
progress of the external solver or the internal solver will give some
hints about its overall progress. The later isn't really a proper
progress as it will jump forward after each substep, but that is at
least a bit better than before without any progress indication.
Fixes also the 'strange' non-display of this progress line in -q=1, while
all others are shown, which is reflected by all testcase changes.
|
|
The unpack of a M-A:same package will force the unpack of all its
siblings directly to prevent that they could be separated by later
immediate actions. In commit 634985f8 a call to SmartConfigure was
introduced to configure these packages at the time the installation
order encounters them. Usually, the unpack order is already okay, so
that this 'earlier' unpack was not needed and if it wouldn't have been
done, the package would now only be unpacked, but by configuring the package
now we impose new requirements which must be satisfied. The code is
clever enough to handle this most of the time (it worked for 2 years!),
but it isn't needed and in very coupled cases this can fail.
Removing this call again removes this extra burden and so simplifies the
ordering as can be seen in the modified tests. Famous last words, but I
don't see a reason for this extra burden to exist hence the remove.
Closes: 740843
|
|
Multi-Arch: same packages can be co-installed, but need to have the same
version for all installed packages (aka "siblings"). Otherwise the
unsynced versions will fight against each other and the auto-install as
wel as the problem resolver will later have to decide between holding the
packages or to remove one of the siblings (usually a foreign) taking a
bunch of packages (like the entire foreign setup) with them.
The idea here is now to be more pro-active: MarkInstall will fail for
a package if the siblings aren't synced, so we don't allow a situation
in which a resolver has to decide if to hold or to remove-upgrade under
the assumption that the remove-upgrade decision is always wrong and
doesn't deserve to be explored (expect valid out-of-syncs of course).
Thats a pretty bold move to take for a library which is used by
different solvers so this check is done in IsInstallOk and can be
overridden if front-ends want to.
|
