diff options
Diffstat (limited to 'data/perl_/Policy.sh')
| -rw-r--r-- | data/perl_/Policy.sh | 162 |
1 files changed, 0 insertions, 162 deletions
diff --git a/data/perl_/Policy.sh b/data/perl_/Policy.sh deleted file mode 100644 index 10a7919a1..000000000 --- a/data/perl_/Policy.sh +++ /dev/null @@ -1,162 +0,0 @@ -#!/bin/sh -# -# This file was produced by running the Policy_sh.SH script, which -# gets its values from config.sh, which is generally produced by -# running Configure. -# -# The idea here is to distill in one place the common site-wide -# "policy" answers (such as installation directories) that are -# to be "sticky". If you keep the file Policy.sh around in -# the same directory as you are building Perl, then Configure will -# (by default) load up the Policy.sh file just before the -# platform-specific hints file and rewrite it at the end. -# -# The sequence of events is as follows: -# A: If you are NOT re-using an old config.sh: -# 1. At start-up, Configure loads up the defaults from the -# os-specific hints/osname_osvers.sh file and any previous -# Policy.sh file. -# 2. At the end, Configure runs Policy_sh.SH, which creates -# Policy.sh, overwriting a previous Policy.sh if necessary. -# -# B: If you are re-using an old config.sh: -# 1. At start-up, Configure loads up the defaults from config.sh, -# ignoring any previous Policy.sh file. -# 2. At the end, Configure runs Policy_sh.SH, which creates -# Policy.sh, overwriting a previous Policy.sh if necessary. -# -# Thus the Policy.sh file gets overwritten each time -# Configure is run. Any variables you add to Policy.sh will be lost -# unless you copy Policy.sh somewhere else before running Configure. -# -# Allow Configure command-line overrides; usually these won't be -# needed, but something like -Dprefix=/test/location can be quite -# useful for testing out new versions. - -#Site-specific values: - -case "$perladmin" in -'') perladmin='saurik@carrier.saurik.com' ;; -esac - -# Installation prefixes. Allow a Configure -D override. You -# may wish to reinstall perl under a different prefix, perhaps -# in order to test a different configuration. -# For an explanation of the installation directories, see the -# INSTALL file section on "Installation Directories". -case "$prefix" in -'') prefix='/usr' ;; -esac - -# By default, the next three are the same as $prefix. -# If the user changes $prefix, and previously $siteprefix was the -# same as $prefix, then change $siteprefix as well. -# Use similar logic for $vendorprefix and $installprefix. - -case "$siteprefix" in -'') if test "/usr/local" = "/usr"; then - siteprefix="$prefix" - else - siteprefix='/usr/local' - fi - ;; -esac -case "$vendorprefix" in -'') if test "" = "/usr"; then - vendorprefix="$prefix" - else - vendorprefix='' - fi - ;; -esac - -# Where installperl puts things. -case "$installprefix" in -'') if test "/usr" = "/usr"; then - installprefix="$prefix" - else - installprefix='/usr' - fi - ;; -esac - -# Installation directives. Note that each one comes in three flavors. -# For example, we have privlib, privlibexp, and installprivlib. -# privlib is for private (to perl) library files. -# privlibexp is the same, except any '~' the user gave to Configure -# is expanded to the user's home directory. This is figured -# out automatically by Configure, so you don't have to include it here. -# installprivlib is for systems (such as those running AFS) that -# need to distinguish between the place where things -# get installed and where they finally will reside. As of 5.005_6x, -# this too is handled automatically by Configure based on -# /usr, so it isn't included here either. -# -# Note also that there are three broad hierarchies of installation -# directories, as discussed in the INSTALL file under -# "Installation Directories": -# -# =item Directories for the perl distribution -# -# =item Directories for site-specific add-on files -# -# =item Directories for vendor-supplied add-on files -# -# See Porting/Glossary for the definitions of these names, and see the -# INSTALL file for further explanation and some examples. -# -# In each case, if your previous value was the default, leave it commented -# out. That way, if you override prefix, all of these will be -# automatically adjusted. -# -# WARNING: Be especially careful about architecture-dependent and -# version-dependent names, particularly if you reuse this file for -# different versions of perl. - -# bin='/usr/bin' -# scriptdir='/usr/bin' -# privlib='/usr/lib/perl5/5.10.0' -# archlib='/usr/lib/perl5/5.10.0/apple-darwin8' -# Preserving custom man1dir -man1dir='/usr/share/man/man1' -# Preserving custom man3dir -man3dir='/usr/share/man/man3' -# Preserving custom html1dir -html1dir=' ' -# Preserving custom html3dir -html3dir=' ' -# sitebin='/usr/local/bin' -# sitescript='/usr/local/bin' -# Preserving custom sitelib -sitelib='/usr/local/lib/perl5/site_perl/5.10.0' -# sitearch='/usr/local/lib/perl5/site_perl/5.10.0/apple-darwin8' -# Preserving custom siteman1dir -siteman1dir='/usr/local/share/man/man1' -# Preserving custom siteman3dir -siteman3dir='/usr/local/share/man/man3' -# Preserving custom sitehtml1dir -sitehtml1dir='' -# Preserving custom sitehtml3dir -sitehtml3dir='' -# vendorbin='' -# vendorscript='' -# vendorlib='' -# vendorarch='' -# Preserving custom vendorman1dir -vendorman1dir=' ' -# Preserving custom vendorman3dir -vendorman3dir=' ' -# Preserving custom vendorhtml1dir -vendorhtml1dir=' ' -# Preserving custom vendorhtml3dir -vendorhtml3dir=' ' - -# Lastly, you may add additional items here. For example, to set the -# pager to your local favorite value, uncomment the following line in -# the original Policy_sh.SH file and re-run sh Policy_sh.SH. -# -# pager='/usr/bin/less' -# -# A full Glossary of all the config.sh variables is in the file -# Porting/Glossary. - |